Search Results (7K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
I have added an additional physical disk my PowerEdge 650 server.After the disk was ready i logged into the IDRAC and added it to the existing raid and started the reconstruction which took about 24 hours to complete fully.The drive is now showing to be part of the raid 5 and the size of the raid on
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
Hello , I have to disable SSH on all of my Dell IDRACs because of Security Reasons . I also want to configure SNMP with our Community String . I created an Template to rollout to al IDRACS so that SNMP become enable and also shows our Community String . That works fine and i can choo
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hi, I have a server with a failed main board, I bought a replacement (ebay) which doesn't have an iDRAC enterprise licence. How can I transfer the licence from the failed board to the new (used) board? Thanks in advance.
Question
•
Systems Management General
Community Accepted Solution
Hello together, I am asking for a friend...After we have discovered a new server with OME 4.1.0, a new user (OME_29fbxxxxx) with the Administrator user role appears on the iDRAC board under the local users. So far we have no idea how this is generated and why. We have only been using this latest OME
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello, I understand that when deploying the appliance that 2*415GB hard drives are required. Do both hard drives need to reside on the same datastore or can they reside on 2 different datastores? Thanks in advance,
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hi . Same problem on my server. ı m confused then ı had angry. Could you help me this problem :) When i firmware update on F10 Lifecyle . That is seen this error SWC0066. My internet is normal. Modem rule is normal. ı have no Firewall and switch . I did NVRAM clear . check other compenent bu
Question
•
Rack Servers
Community Accepted Solution
Hi all, I have a Dell R730 with 2 x Xeon E5-2673v4 (20 core), 256 GB RAM, 16 x 2.5" Crucial 2TB SSD configured as a RAID-10 with a H730 Perc controller. On this device are 20 VMs, each configured with 8GB of RAM and 4 vCPU. A couple of the users logging in via RDP are saying that the response time
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi~ Is there any plan to support Xen server with perc 12?
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
We successfully migrated from a working OMIVV to OMEVV. I am trying to register the OMEVV Plugin. Version: 1.3.0.1581. I get the error attached. Running vSphere Client version 7.0.3.01700 Troubleshooting the plugin, "/core/console/console.html#/omc/troubleshoot", I can ping our vcenter server, whic
Question
•
OpenManage Integration for VMware vCenter
Community Accepted Solution
Hi all, Does someone know the part number of this piece? Poweredge R340 right ear Thanks in advance,
Question
•
PowerEdge Hardware General
Community Accepted Solution
I have a Dell R740 with the Ethernet 10G 4P X520/I350 rNDC Card installed. If i use the old firmware update file for 22.0.9 Release, the NVM Update Tool finds the card and would update the firmware. Num Description
Question
•
Rack Servers
Community Accepted Solution
Hello, I am trying to monitor the CPU utilization for the PowerEdge FN 410S IOM via SNMP. Does anyone know the OID for this sensor or if it is possible to query? Thank you, Matthew
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
Hello, how can I wipe the hard drive for a M610. I can go back to defaults with the IRDAC and Bios, but I cannot seem to find a way to wipe the hard drive on the unit. I do not see a Retire or repurpose option in the Lifecycle setup
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi I want to upgrade my server PowerEdge R730 second processor What equipment needed? Please advise
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello, hope everyone is doing well. Question - If I want to install 2 GPUs in a PowerEdge R940XA server, then would I just need the 16x risers and respective cables? Is there a part number for a GPU Enablement Kit? Thank you
Question
•
PowerEdge Hardware General
Community Accepted Solution
I have just deployed OpenManage Enterprise 4.0.1 however when I check the catalog management, I get the error: Execution Message Running Processing repository information. Attempting to connect to repository. Downl
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Kind of using this as a last resource as I cannot seem to fix this on my own. I have a new to me PowerEdge 2970 (yes I know the server is well past support and should absolutely be replaced by today's standards; however, it is only used for home/remote storage and it fits my needs perfectly for what
Question
•
Rack Servers
Community Accepted Solution
I am unable to find any compatibility list for the PowerEdge R760sx, can someone tell me if it is compatible with the Intel x520 line? If not, what are the suggested cards for this system and CentOS 7? Thanks!
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello! I failed finding information on the Dell U.2 enablement kit P31H2 so I am asking here. Does this card absolutely have to be installed in an x16 PCIe Slot or will it work at a x8 as well (with reduced max. speed)? What does the card do exactly? Splitting 16 lanes into 4x4 with bifurcation s
Question
•
Rack Servers
Community Accepted Solution
Hello, I'm trying to expand existing RAID10 on PowerEdge R740xd. Currently we have 8 drives configured as RAID10. I bought 2 extra drives of the same size, and added in to the server. Then I've logged in to iDRAC 9, In the disks menu i see two newly added drives that currently are in the state: read
Question
•
Systems Management General